How to Remove and also Change a Bathtub.
How to Remove and also Change a Bathtub.
Blog Article
They are making a few great annotation related to A Step-by-Step Guide to Installing a Bathtub as a whole in this post following next.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably hard project. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and do not require to transform the setup of your previous water supply pipelines.
Your devices and also product list need to consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and also examine all joints and brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Getting ready for the Installation
First of all, the supporting framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on Installing A Bathtub. Thanks a ton for taking the time to read our post. Do you know another individual who is serious about the topic? Please feel free to share it. Many thanks for your time. Come back soon.
Schedule Appointment Now Report this page